E-Bike Troubleshooting

E-bike battery fully charged but not working: 5 checks

What Bosch, Shimano, Panasonic, Rad Power Bikes, Aventon, Lectric, Ride1Up, Gazelle and Conor say a charged but dead e-bike means, in one table, with the voltages that tell a battery fault from a bike fault.

The short answer

An e-bike battery that is fully charged but not working is usually switched off, asleep or not making contact, not empty. Rad Power Bikes and Aventon list five causes: low charge, faulty connections, a battery not fully seated, the wrong switch-on sequence and a brake lever held. Shimano and Conor batteries wake when the charger is connected. A 48 V pack reading under 32.5 V needs a dealer.

Key takeaways

  • Rad Power Bikes and Aventon print the same five causes for a bike that 'doesn't work': insufficient charge, faulty connections, a battery not fully seated, an improper turn-on sequence and brakes applied.
  • Most e-bikes need two switches: the battery (key or button) and the display. Bosch shuts the whole system down after 10 minutes without movement or a button press.
  • A green charger light is not proof of a full battery: Ride1Up's chargers show green when they are ready to charge, before any battery is connected.
  • Shimano and Conor both say a battery that shows no light at all can be woken by connecting its charger. Bosch says no light can mean a damaged pack, so it goes to the dealer.
  • On a 48 V pack, 54.6 V is full and 32.5 V is the floor of the cells, our calculation from Panasonic's NCR18650B datasheet. Below that, don't charge it at home.

Quick steps

15 min Tools: The bike's key, A soft damp cloth, A digital multimeter (optional, step 5)
  1. Switch on in the maker's order

    Turn the battery on with its key or button, then hold the display's power button. On a Bosch bike, press the on/off button again if the system has been still for 10 minutes.

  2. Unplug the charger and release the brakes

    Pull the charging plug out and let go of both brake levers. A Bosch drive stays locked while the charging cable is plugged in, and Rad and Aventon list error 25 for a brake held at switch-on.

  3. Reseat the battery and clean the contacts

    Switch the battery off, take it out, wipe the battery and holder contacts with a soft damp cloth, and refit it until it clicks and locks. Pull apart and refit any quick-plug connectors without twisting.

  4. Read the battery's own lights

    Press the button on the battery. Bosch: no LED can mean damage, two flashing LEDs a defect, three flashing LEDs a temperature fault. Panasonic: lamps 1, 3 and 5 flashing mean temperature.

  5. Wake it with the charger

    Connect the bike's own charger for a few minutes. Shimano and Conor both say the charger releases a battery that has switched itself off. If nothing lights after that, take the battery to the dealer.

An e-bike battery that is fully charged but not working is almost always switched off, asleep or not making contact, and only rarely empty or broken. The five checks below come from the makers’ own manuals, in the order they list them, and most bikes are running again by check three.

This guide is for anyone standing next to a dead e-bike with a charger that says the battery is full. Every instruction below is quoted from the maker’s manual or help page, checked November 16, 2026, and every voltage is our calculation from a cell maker’s datasheet. We have not tested these batteries ourselves.

Why does a fully charged e-bike battery not work?

A fully charged e-bike battery does not work when power can’t get from the cells to the motor. Rad Power Bikes and Aventon print the same five causes, word for word, in their troubleshooting tables.

Their table for a bike that “doesn’t work” lists insufficient battery power, faulty connections, a battery not fully seated in its tray, an improper turn-on sequence, and brakes that are applied. Only the first of the five is about charge. The other four mean the battery is fine and something between it and the motor is open. That matches how the battery management system works: it can switch the output off to protect the cells while the charge stays where it was.

Bosch’s operating instructions describe exactly that switch. Its Electronic Cell Protection guards against deep discharge, overcharging, overheating and short circuits, and “a protective circuit automatically switches off the battery pack” in a hazardous situation. A switched-off pack can hold 100% and still give the motor nothing.

What do nine makers say a charged but dead e-bike means?

Nine makers’ manuals agree on the shape of the problem and disagree on the cure. The table puts each one’s switch-on and its advice for a battery that shows no life side by side.

Maker (document)How the system switches onWhen a charged battery shows no life
Bosch (classic Performance Line instructions)On/off button on the battery or the on-board computer; shuts down after 10 minutes stillNo LED can mean a damaged pack: don’t charge it, see a Bosch dealer
Shimano (UM-7GP0B-005)Battery power switch; can’t switch on while chargingProtection circuit may be on: connect the charger to release it
Panasonic (Japanese FAQ)The FAQ covers the battery’s lamp patterns onlyLamps 1, 3 and 5 flashing: temperature, wait 2 hours or more at 0 to 40 °C
Rad Power Bikes (2019 RadWagon manual)Key to position 1, then hold “mode” about 2 secondsCheck charge, connections, seating, sequence and brakes
Aventon (Aventure manual)Quick press on the battery, then hold the display buttonSame five causes as Rad, same error 25
Lectric (help center)Key to ON, then hold the display power buttonCheck key position and pull apart the quick plugs, don’t twist
Ride1Up (support pages)Button on the battery shows its chargeIf nearly dead and the bike powers off, don’t drain it further
Gazelle (Belgian and Dutch support)DisplayMotor off on the display, wait 10 seconds, restart; check the charger first
Conor (Spanish battery manual)Button on the battery“Deep Sleep”: the charger is the only signal that wakes it

The split matters. Shimano and Conor tell you to connect the charger to a battery that shows nothing. Bosch tells you that the same symptom can mean damage and the battery should not be charged. Follow the instruction for your own system, which is printed on the battery or the motor, not the advice for someone else’s.

Conor’s manual is the only one that says when its battery falls asleep: a draw under 200 mA for more than 10 minutes, the bike switched on and standing still for that long, or storage nearly empty for weeks. That covers a bike left on in the hallway overnight, which is the commonest story behind “it was full yesterday.”

Does a green charger light mean the battery is full?

A green charger light does not prove the battery is full. On some chargers green only means the charger has power and nothing is flowing.

Ride1Up says plainly that “all Ride1UP chargers will show a green light indicating it is ready to charge,” which is before any battery is connected. Rad Power Bikes’ charger shows two red lights while charging and one green plus one red when done. Aventon’s shows red then green, and Conor’s solid red then solid green. Shimano’s charger LED flashes for a charge error and stays off when no battery is connected.

So a charger that went green in five minutes on a battery you rode empty yesterday did not fill it. Either the plug never made contact or the battery refused the charge. Our charging time calculator gives the hours a real full charge takes for your battery size and charger amps, which is the quickest check that the green light is telling the truth.

How do you fix a charged e-bike battery that won’t power the bike?

Work the five checks in this order. They take about 15 minutes, and only the last one needs a tool you might not own.

  1. Switch on in the maker's order

    Turn the battery on with its key or button first, then hold the display's power button. Rad says to hold the mode button about 2 seconds, Lectric until the display lights. On a Bosch bike that sat still for 10 minutes, the whole system is off, so press on/off again.

  2. Unplug the charger and release the brakes

    Pull the charging plug out of the battery and let go of both levers. The Bosch battery guide says plugging in the charging cable locks the drive unit, and Shimano says its system can't switch on while charging. Rad and Aventon list error 25 for a brake applied while turning on.

  3. Reseat the battery and clean the contacts

    Switch the battery off, open the lock with the key and take it out. Wipe the battery and holder contacts with a soft damp cloth, as Bosch's instructions say, then refit it until you feel and hear it click and lock it. Lectric's quick-plug connectors are pulled straight apart, checked and pushed back with the arrows aligned, never twisted.

  4. Read the battery's own lights

    Press the button on the battery itself. On a classic Bosch pack each of the five LEDs is about 20%, and below 5% they all go out. Two flashing LEDs mean a defect, three mean the battery is outside 0 to 40 °C. On Panasonic packs, lamps 1, 3 and 5 flashing mean a temperature fault.

  5. Wake it with the charger

    Connect the bike's own charger to the battery, then to the wall. Conor says to wait 2 to 5 minutes for a red or yellow LED, and if the battery fell asleep while connected, to unplug, wait 30 seconds and reconnect. If nothing lights, stop here and take the battery to the dealer.

Diagram of the power path from an e-bike battery to the motor with five checkpoints: the switch-on sequence (two switches, Bosch auto-off after 10 minutes), the charger plug and brake levers (error 25), the battery seating and contacts, the battery LEDs (each Bosch LED about 20%, under 5% all off) and the charger wake-up (Conor waits 2 to 5 minutes). A 48 V pack reads 54.6 V full and 32.5 V at the cell floor.
Power has to pass all five checkpoints to reach the motor. Check them in this order; the first one that is open is the fault. · Riding Nexus diagram from Bosch, Shimano, Rad Power Bikes, Aventon, Lectric and Conor manuals, checked November 16, 2026. Voltages are our calculation from Panasonic's NCR18650B datasheet.

If the temperature was the cause, give it time. Shimano says to leave the bike at 0 to 50 °C for a while before trying again, and Panasonic asks for two hours or more at 0 to 40 °C, half a day in some cases. A battery brought in from a frozen garage needs that wait before any of the checks mean anything.

Our guide to resetting an e-bike battery has each maker’s reset procedure and wait times in detail, including the ones that conflict.

How do you tell a battery fault from a bike fault?

A display that lights up tells you the battery is delivering power, so the fault is in the motor side: wiring, throttle, motor plug or the motor itself, which are the four causes Rad Power Bikes and Aventon list when “the motor does not respond when the bike is powered on.” A dark display and a dark battery point back to the battery.

On bikes with a key or a button on the battery and a published charger voltage, a multimeter settles it. Panasonic’s NCR18650B datasheet charges a cell to 4.20 V, calls 3.6 V nominal and stops discharge at 2.50 V. Multiply by the number of cells in series and you get the three numbers that matter.

PackFull off the chargerCell floor (do not charge at home below this)
36 V (10 cells in series)42.0 V25.0 V
48 V (13 cells in series)54.6 V32.5 V
52 V (14 cells in series)58.8 V35.0 V

If a 48 V pack that the charger called full reads close to 54.6 V at its discharge terminals, the battery is fine and the fault is in the key switch, the contacts or the bike. If it reads 0 V, the battery has switched its output off, which is a sleep or protection state, not a flat battery. If it reads under 32.5 V, at least one group of cells is under the cell maker’s discharge floor. We would not charge that pack at home and would take it to the bike’s maker.

Bosch and Shimano publish no terminal voltage test for their batteries, so for those systems the battery’s LEDs and the dealer are the route. The full chart, including the voltages Ride1Up’s displays use for each bar, is in our e-bike battery voltage chart.

What do riders get wrong when a charged battery won’t work?

The commonest mistake is treating “charged” as “on.” Most hub-motor bikes need the battery switched on with its key or button and the display switched on separately, and Lectric adds that the headlight works only when the battery is on. A bike that charged overnight with the key at OFF will look dead in the morning.

Second, riders trust the charger light over the battery’s own lights. Ride1Up’s green means ready, not full. Press the button on the battery and count its LEDs before you decide anything.

Third, riders keep holding a brake lever while switching on, or leave a lever sensor stuck. Rad Power Bikes and Aventon both give that its own code, error 25.

Fourth, riders drain the battery flat to “reset” it. Bosch’s battery guide says to avoid complete discharge, and Ride1Up says that if a battery is nearly dead and the bike powers off, don’t power it up or drain it any further. Our winter storage guide covers the storage levels that stop a pack falling into a protection state in the first place.

Fifth, riders buy a new battery before checking the charger. Gazelle says to rule out the charger first, and a new Gazelle battery costs €400 to €900. Across our e-bike price comparison, a maker’s spare battery costs 25% to 30% of the bike, so a borrowed charger that fixes the problem is a large saving.

Where these instructions come from

Every instruction comes from the maker’s own manual or help page, read November 16, 2026: Bosch eBike Systems’ operating instructions for its classic Performance Line system and its battery guide, Shimano’s manuals UM-7GP0B-005 and UM-7K10A, the 2019 Rad Power Bikes RadWagon manual, Aventon’s Aventure manual, Lectric’s and Ride1Up’s help centers, Gazelle’s support pages, Conor’s battery manual and Panasonic’s Japanese FAQ. Shimano’s server refuses automated downloads, so its three instructions were read from the manuals’ indexed text, not the full PDF. Bosch’s Smart System help center was down for maintenance, so the Bosch rows describe the classic system.

The voltages are our calculation from Panasonic’s NCR18650B datasheet. The stop instruction comes from Samsung SDI and the UK Department for Transport, and the fire figure from the London Fire Brigade. More fixes are in the e-bike troubleshooting hub.

Frequently asked questions

Can an e-bike battery be fully charged but dead?

An e-bike battery can be fully charged and still deliver nothing when its protection circuit has switched the output off. Bosch says a protective circuit switches the battery off in hazardous situations, and Shimano says its protection circuit can stop the battery lighting up until the charger is connected. A switched-off battery is not an empty one.

Why does my e-bike display turn on but the motor doesn't work?

When the e-bike display turns on but the motor doesn't work, the battery is delivering power and the fault is further along. Rad Power Bikes and Aventon list loose wiring, a loose or damaged throttle, a loose motor plug wire and a damaged motor, and both name error 25 for a brake lever held while switching on.

Does cold weather stop a charged e-bike battery from working?

Cold can stop a charged e-bike battery from working until it warms up. Bosch rates its classic batteries for use from -10 to 40 °C (14 to 104 °F) and flashes three LEDs outside the 0 to 40 °C charging range. Panasonic asks you to wait two hours or more at 0 to 40 °C after a temperature warning.

How long does an e-bike battery last before it stops working?

An e-bike battery usually lasts 4 to 5 years, according to Gazelle, which prices a new one at €400 to €900. A battery that is near the end of its life loses range first; Bosch says a clearly shorter riding time after a full charge means the pack is worn out and needs replacing.

Sources & references

We cite primary sources wherever possible: standards bodies, regulators, manufacturers and peer-reviewed research. See our editorial policy.

  1. Bosch eBike Systems original operating instructions, Performance Line drive and battery packs (0 276 001 SPI) Bosch eBike Systems
  2. Your eBike battery guide (EN-GB) Bosch eBike Systems
  3. Battery safety Bosch eBike Systems
  4. Special battery and parts user's manual, UM-7GP0B-005 Shimano
  5. SHIMANO STEPS special battery and parts user's manual, UM-7K10A-004 Shimano
  6. SHIMANO STEPS special battery and parts user's manual, UM-7K10A-002 Shimano
  7. 2019 RadWagon owner's manual (USA) Rad Power Bikes
  8. Aventure owner's manual (English) Aventon
  9. First ride questions Lectric eBikes
  10. My bike won't turn on? Display is blank Lectric eBikes
  11. All about batteries Ride1Up
  12. Battery display: voltage and percentage readouts Ride1Up
  13. Problemen met je e-bike Gazelle
  14. Accu problemen Gazelle
  15. Manual del usuario: batería de ion-litio Conor Bikes
  16. バッテリーが変な点滅をするのですが(リチウムイオン) Panasonic
  17. NCR18650B lithium-ion cell datasheet Panasonic
  18. Battery safety information Samsung SDI
  19. Battery safety for e-cycle users UK Department for Transport
  20. E-bikes and e-scooters London Fire Brigade

Up next

Hand-picked guides that go deeper on e-bike troubleshooting and e-bikes.

Explore E-Bikes